2Ys Free Update Autel MaxiIM IM608 ADVANCED IMMO & KEY PROGRAMMING Get Free APB112 Smart Key Simulator + G-BOX3 + AUTEL MaxiAP AP200H

Tech support

Original Autel MaxiIM IM608 VS IM508 VS Auro IM600 VS IM100

Autel factory combine EOBD2shop.com engineer make a comparison table about Autel MaxiIM IM608 VS Autel MaxiIM IM508 VS Auro OtoSys IM600 VS Auro OtoSys IM100. They can compare with each other in the aspects of IMMO (key programming, key learning, pin code read etc.), programming, OE-Level diagnosis, Advanced Service Functions, configurations etc.

Here we go for details:

Product	Autel MaxiIM IM508	Autel MaxiIM IM608	AuroOtoSys IM100	AuroOtoSys IM600
Image
IMMO
Smart Mode (Guided and Automated Key Learning Function)	√	√	√	√
Expert Mode (Advanced key Learning)	√	√
Auto Detect Make/Model/Year/System			√	√
Read PIN/CS			√	√
Read PIN/CS (All Keys Lost)	√	√	√	√
Key Generation	√	√
Key Learning	√	√	√	√
IMMO ECU Reset/Adaption	√	√	√	√
IMMO ECU Refresh/Coding	√	√	√	√
Remote Learning	√	√	√	√
Backup /Restore IMMO Data	√	√
AUDI Q5/A4/A5 2015-2017 Read PIN/CS			N/A	√
BMW FEM/BDC Key Learning and Adaption			√	√
Mercedes Key Learning			×	√
Benz 3rd Generation IMMO Add key, all key lost, key Learning	N/A	√
BMW FEM/BDC Key Learning and ECU adaptation	√	√
BMW CAS4/3/2 key learning	CAS4 available when connected to XP400	√
VW /Audi MQB (VDO & JCI) add key, IMMO V A4/A5/Q5 2015+ Key learning	N/A	√
VW /Audi /Skoda / Seat IMMO III /IV /V add key, all key lost	√	√
Programming
Key read /write	√	√
EEPROM Read/Write	√	√	√	√
MCU Read/Write	Basic	Advanced	Basic	Advanced
ECU Read/Write	When connected to XP400	√
MC9S12 Encryption Chip read/write	When connected to XP400	√
IC Card Read/Write	When connected to XP400	√	N/A	√
Mercedes Infrared Key Read/Write	When connected to XP400	√	N/A	√
Remote Frequency Detect	When connected to XP400	√	N/A	√
Support PC	When connected to XP400	√
OE-Level Diagnostics
All Systems for Over 80 Makes and Models	N/A	√	√	√
AutoVIN /Auto scan	√	√
Read /Erase codes	√	√
View, record, playback live data	√	√
View Freeze Frame data	√	√
Shop and data Manager applications	√	√
MaxiFlash JVCI ECU Reprogrammer (Bluetooth /USB cable)	N/A	√
OtoFlash (J2534 ECU Reprogrammer)			N/A	√
Advanced Service Functions
Oil Serive Reset	√	√	√	√
Parking Brake Pad Relearn After Replacement	√	√	√	√
Steering Angle Sensor Relearn	√	√	√	√
Battery Registration and Reset	√	√	√	√
Diesel Particulate Filter Regeneration	√	√	√	√
Tire Pressure Monitoring System Sensor ID Relearn	√	√	√	√
ECU Coding	N/A	√	N/A	√
VW/Audi Component Protection			N/A	√
Complete Service Functions	N/A	√	N/A	√
Tool Features
Built-in Rechargeable Li-ion Battery	5000 mAh	15000 mAh	5000 mAh	15000 mAh
Internet Updatable	Wi-Fi	Wi-Fi	Wi-Fi	Wi-Fi
Multilingual Support	√	√	√	√
One Year Warranty	√	√	√	√
Free Online Update Two Years	√	√	√	√
Touchscreen	7-inch	10.1-inch	7-inch	10.1-inch
Memory	32 GB	64 GB	32 GB	64 GB
Processor	Cortex-A9 processor	Cortex A7+A15 six-core processor	Quad-core processor	Hexa-core processor
Camera	N/A	8.0 Megapixel	N/A	8.0 Megapixel
Resolution	1024×600	1920×1200	1024×600	1920×1200
Note: XP400 can be purchased separately.
Some listed functions are manufacture dependent. Constantly update MaxiIM for current vehicle coverage. Update software regularly for most accurate tool features.

Autel MaxiIM IM608 Review by user:
I go to Autel IM608 Volvo application, then choose Manual selection. I find that IM608 supports XC60 made in 2008-2018. I use a USB cable to connect the vci device to improve connection speed. It’s a important step to turn off Bluetooth first before use the USB. Then I insert the learned key into the key slot and turn the ignition on. After that, I turn the ignition off and remove the key from the key slot. Then it starts to establish vehicle communication. You need to know if a key is to be learned, insert the new key into the key slot and press learning button to continue. Very lucky, the key learns successfully. I take out the key and insert it again to test the functionality.

Autel IM608 is one of  the most advanced all in one,Combines  IMMO key programming, all systems diagnostics and advanced service.








How to Update Autel MaxiIM IM608 Software:
Autel IM608 Update application allows you to download the latest released software.
The updates can improve the MaxiIM applications’ capabilities, typically by adding new tests, new models, or enhanced applications to the database. The Display Tablet automatically searches for available updates for all of the MaxiIM software when it is connected to the internet. Any updates that are found can be downloaded and installed on the device. This section describes installing an update to the MaxiIM System. A notification message displays if an update is available when the Notifications Center function is enabled in the Settings application.

1. Make sure the Display Tablet is connected to a power source with stable access to the internet.
2. Tap the Update application button from the MaxiIM Job Menu; or tap the update notification message when received one; or tap the Update icon on Vehicle Menu in Diagnostics application. The Update application screen displays.
3. Check all available updates:
--If you decide to update all the items of IMMO software, select IMMO Tab and then tap the Update All button; if you want to update all items of diagnostic software, select Diagnose Tab and then tap the Update All button.
-- If you only want to update one or some of the item(s), tap the Update button on the right column of the specific item(s).
4. Tap the Pause button to suspend the updating process. When you tap Continue to renew the update, the updating process will resume from the break point.
5. When the updating process is completed, the firmware will be installed automatically. The previous version will be replaced.

How to Pair the MaxiFlash with the IM608 Tablet?
1. Power on the tablet.
2. Insert the 16-pin vehicle data connector of the MaxiFlash to the vehicle data link connector (DLC).
3. Tap the VCI Manager application on the MaxiFlash Job Menu of the tablet.
4. Select BT from the connection mode list.
5. Tap the Scan button at the top right corner. Now the device starts searching for available pairing units.
6. The device name may display as MaxiFlash suffixed with a serial number. Select the appropriate device for pairing.
7. When paring is successfully done, the connection status displayed to the right of the device name is shown as Paired.
8. Once paired, the VCI button on the system Navigation bar at the Connection LED on the MaxiFlash illuminates solid blue.
This signifies that the tablet is connected to the MaxiFlash, and is ready to perform vehicle diagnosis.
9. Tap the paired device again to unpair it.
10. Tap the Home button on the top left to return to the MaxiIM Job Menu

See questions and answers