A:Main steps:
Remove the RFA
Read D-flash and EEPROM
Perform Start key writing to generate new data
Write the new data back to RFA
Assemble the vehicle
Verify the key function
Procedure:
Remove the KVM/RFA Module Secured Module and open cover
see 2017 2018 Jaguar and Land Rover KVM Location
Go to Immo Programming- Jaguar- Manual Selection- F-PACE – 2017-2018 Smart Key
Conform vehicle info
Select Control Unit- Start Key Writing
Autel IM608 will show you start key writing instruction and wiring diagram
Read Chip status in Unsecured mode
the adapter is soldered according to the “unlocked” scheme and the status of the chip is read.
The chip is locked. So desolder 2 components
Then solder adapter according to the scheme and two components must be removed from the circuit board.
with the macthing wire harness APA106 of the xp400/xp400 pro, connect the wire as wiring diagram, T1 and T2 indicate the two components to be removed. After all function completed, the two components needs to be re-installed during vehicle assembly.
Select Read/Write Chip (secured)
Read and save eeprom and d-flash separately
Read MCU Data
Read D-flash and EEPROM step by step
Then select Start Key Writing functio
Select D-flash file then select EEPROM file read above
Select an unused key position and Add key
Make sure device is well connected and place a key to be programmed into xp400 programmer
Program dealer key successfully
Exit key writing and save new Dflash and EEPROM data
The data file is saved. Write back new data.
Select Read/Write Chip (secured)->Write MCU data
Select new D-flash data and write chip
Select new EEPROM data and write chip
Then verify Key ID
Solder back two components, install RFA module back to vehicle
Test the new key.
It is working. Done.

A:You lose online access for key programming and autel support.

A:Im508/im608 works very well for BMW cas modules. They can do via OBD, but better on bench.

A:it is used with im608 tablet to perform the ASIAN , USA, EU and china brands vhicles key programming, ECU coding, serivices and maintenance hot functions, etc. It can also be used with the OE software to programming the OE software funcitons.

A:yes, IM608 can support the function you will need to do .

A:
only VW $10 or $20 MQB, it'll open a PayPal portal you can sign in or pay by card.
Sometimes it says its paid but you get it free.
Just follow IM608 operation.

A:Please hold down the camera icon at the bottom of the screen for a few seconds

A:
You can still do some keys but anything that requires server calculations obviously won't be accessible without an active subscription.
if you try to program a Mercedes or Kia/Hyundai you won’t be able to get a calculation for password or pin.
It is recommended to subscribe the update license.

A:
1. Yes it has special card slot
2. Yes

A:online coding, programming needs j2534 jvci and online subscription.

A:yes, can work with dealer key as long as the key is not locked.

A:
The IM608 has limited capabilites for ADAS.
It can access ADAS specific modules to view codes and data.
It will be able to perform some dynamic calibrations for vehicles that do not require targets to calibrate. Limited by available coverage and some modules may require programming to do so.
You cannot add Autels ADAS software calibration package to the IM608.

A:Yes, reuqires J2534 + Honda J2534 Rewrite using a Windows based computer.

A:Encrypted KVM cannot be done obd, however, you can use replacement keys, the editable keys via obd. Done quite a few that way.
Bench job in 15 minutes. Perform Start key writing buy removing KVM/RFA from the car.

2010-2015 (ish) Dpla system – obd
2016-2018 (ish) Fk72 system – bench
2017-2019 (ish) Hpla system – bench
2019+ Jpla system – new kvm module, two new keys and a scan tool with doip j2534 interface
Above are the safe way to do Jaguar and Land rover systems with Autel.