Full Version ECUHELP HT-PROG With Softdog Can be Used Independently

Product Description

• Support ECU Clone
• Support ECU Chip tuning
• Works alone and no need to work with ECUHELP KT200
•  HTprog is the latest programming equipment for the automotive electronics industry.
• ECUHELP HTprog includes MPC Module, EEPROM module, OBD2 Cable, BDM adapter, Tricore adapter, Dongle
• Can do chip tuning,DTC removal, adblue removal EGR cancellation, DPF cancellation, hot start, speed limit release, IMMO off , etc . and make ECU-related operations by reading and writing ECU.
• For the repair, calibration and replacement of automotive electronic modules, it can even refresh the key, so that the old key can be a new key and continue to match other vehicles.
• Can also read and write car body modules, such as CAS, SZL, FRM, AIRBAG, EZS, BCM, etc. With this function, you can easily deal with matching keys, unlocking anti-theft, adjusting instruments and repairing airbag computers, etc.

Note: 
1. It is advised to uninstall any antivirus software and disable the firewall before using the ECUHELP HTprog.
2. It is important not to upgrade the software to avoid any potential damage to the hardware.
3. Activation of the HTprog is necessary and should be done using the user's registered email address.
4. Install software version: 1.0.45, free download HTProg software 


HTprog Functions: 
Chip Tuning / ECU Cloning
With HTprog you can read and write P-Flash,D-Flash, External Flash and external EEPROM with the option of automatically checksum correction, you will have many methods in most of ECUS :
1. Factory mode (On Bench for most of ECU/TCU): with this option you don't have to open the ECU cover. Just plug some wires for power and signals and you are ready to go. 

2.Tricore Boot Mode for all Tricore ECU: Opening the ECU is mandatory to connect the boot wire on the ECU board.This method is useful when the ECU is not responding

3.BDM (Background debug mode) 

4.JTAG for Renesas and Freescale

BDM Read / Write
With HTprog you are able to break the protection of immobilizers like CAS in BMW. EIZ / EIS in Mercedes Benz. BCM in Volkswagen and Porsche.etc.

Built in Editors
With HTprog you can edit many Flash data like: 
Edit CAS3+ VIN, ISN and keys 
Edit CAS4,CAS4+ VIN,and ISN
Edit mileage for BMW instrument clusters

Other functions
You can do key reset for many brands like Audi, BMW,MIN, Porsche, Toyota,Fiat, Renault...etc.
Read/Write a wide range of SOP8 EEPROMS.
Works side by side with Autohex to make keys.

Key Features
Master version. One License for all protocols on bench.
Supports one of the largest ECU/TCU list in Cars and Trucks for ECU cloning and Chip Tuning. Supports both old and latest ECU / TCUs from Bosch,Continental, Delphi, Marelli,Denso, Tenic,TRW and Valeo.etc.
Reads all BMW long ISN from BMW DME and DDE including MD1 and MG in F/G series

IMMO BDM Read/Write
With HTprog you are able to break the protection of immobilizers like CAS in BMW, EIZ / EIS in Mercedes Benz.BCM in Volkswagen and Porsche...etc.

How to download ECUHelp HTProg software?

Just free download HTProg software by the following mega link.

https://mega.nz/file/8rJxhB5J#g1jnHe9yBfho7N1Y_0KiZyBM71HwuM6-gyhN4BsW_zg

Software version: 1.0.45

Size: 65.2 MB, no password

Compatible operating systems:

* Windows 7

* Windows 8/8.1

* Windows 10

* Windows 11!

Minimum recommended requirements:

CPU > 2.5 GHz (Intel i5, i7)

RAM > 8GB

NOTE:

1.It is advised to uninstall any antivirus software and disable the firewall before using the ECUHELP HTprog.

2.It is important not to upgrade the software to avoid any potential damage to the hardware.

3.Activation of the HTprog is necessary and should be done using the user’s registered email address.

How to Activate HTProg Software?

After downloading, follow the on- screen prompts to install software.

Connect HTprog Clone Adapter to KT200 device, and then connect to the computer

Run HTprog software, it will prompt you to enter your email address.

Enter your email address and wait for the activation link to be sent to you.

Once the HTprog Clone Adapter is activated for KT200, it is ready to use.
 

• Whatsapp: +8618054815707
• Email: sales@EOBD2shop.com
• Hot line: +8618054815707
• Skype: careucar

EOBD2shop OBDII tool online supplier

• Accepting bulk purchases, We can Offer you wholesale price.
• EOBD2shop is a OBDII tool online supplier providing best-quality ECU chip uning tools, car diagnostic tools, OBDII Code scanners, car key programmers, heavy duty scanners, locksmith tools etc. 
• Besides, we are the agent for many original brand such as Autel, Xhorse, OBDstar, VXdiag, XTOOL,Launch,CGDI, Yanhua ect.