A:It is full master version

A:Yes, purchase update service $250

A:Hi yes, you could get all VR file from us if you buy this product, no need to pay for extra tech cost, you could switch language to french by yourself.

A:Yes, can read both eeprom flash if ECU is not high level protect

A:yes read this ecu Boot_tricore for flash and eprom

A:Yes, it can.

A:Hi friend, yes, Full license all activated.

A:Hi friend, KT200 EU stock still on the way, need to wait for 2 more weeks to come, we could send from local china by 4px express, no need tax too.

A:Yes, some version can be done via OBDvr, most in boot.

A:Solution:
It is easy to figure it out. Bad file or probably checksum not correct.
You write bad file, tool can only write it file it is told to write, just write Ori back to ecu.
Write the ORI file to the car, when it runs you will then see that the file is bad.

Solved.
Correct checksum manually. Checksum written with another program (winols) and 13V power supply

A:Solution:
Copy auto.exe and place it in the KT200-master folder.
https://mega.nz/file/BbVUgDYC#-yVv9clm21JlBRVGdQADJmx1JMzl_5Oy6YhHnT4QSSA
It should be ok.

A:Solution:
Download “auto.txt” file, and put it into “KT200-master” folder.
(Click to Download File)

A:Wrong Gpt connection. You did not connect S1 and S2.
KT200 EDC17CP44 bench pinout

A:EDC17 OTP ERROR solution:- think due to try to write FULL flash not partial. Please read password before writing file for test.
Must read password first to write full flash.
If you have other editor that you can do compare on Original and Modified file to see if any noticeable differences i.e. address location shift, if want send KT200 technician both files as would like to address this problem.

A:1.Do Not connect device, and run “Renew Driver”
2.Connect device, run “Update Firmware” (Do Not disconnect USB cable during update)
3.Run “Setup”, run “KT200.exe”

A:Please download the latest software below to update. (software version will remain the same after update)
V22.10.01-2 KT200 Software Download Link

A:Yes, this ECU is supported by KT200 ECU programmer.
It is in boot mode, check other E6TX pinouts for the same ecu pin layput, will just be Power, GND, K-line, VPP – Mitsubishi keeps the same schema on ECUs.

A:They both are good tools but in different ways. PCMtuner has a lot of obd modules for Asian etc, but cannot do any BDM Jtag work or Agri and plant like KT200.
KT200 has more new protocols and with the possibility of reading TCUs than pcm. But it does not have tuner account and tuning service for tuners.
pcm tuner has better technical support and no annual fee. kt200 uses an annual subscription model for updates.
Each tool has their own capabilities, no all tools can do read/write perfectly. Buy both, PCMtuner has very good coverage but can only do certain bench jobs (edc17/med17/mev17) and limited boot. It depends on your needs, no one tool is ever enough. The 2 machines are complemented. The more tools, the more work you can perform.

A:Solution
Update >> Reset Device;
Unplug the KT200 USB port, then reconnect it;

Click “Reset Device” again to open the software normally.
Hope this can help.
If you still have problem, please contact us with device SN.

A:Solution: Copy the DFB2XX.dll file to the C:\Windows\SysWOW 64 directory, if it is a 32-bit system, the path is C:\Windows\System32
DFB2XX.dll file Download free:
https://mega.nz/file/t4xmhIoC#BBzV4tnoacSGA3vB-AwQDVP7gzWwT7ouSd2-yqm_Qqk
Note: The files in this link are cmopressed packages, which must be unzipped before replacement.